Thanks Sean,
I'll do some flow level experiments near the air intake of the CO2
scrubber, that's the only place where dry air will be flowing
consistently. The other alternative is to make up a separate small fan for
it.
Regards Alan
----- Original Message -----
From: "Sean T. Stevenson" <cast55@telus.net>
To: <personal_submersibles@psubs.org>
Sent: Thursday, February 24, 2011 1:48 PM
Subject: Re: [PSUBS-MAILIST] Oxygen Analyzer
> You want to avoid mounting an oxygen sensor in a manner that will lend
> itself to moisture condensation on the sensor. In rebreathers, the
> sensors are typically placed in the breathing loop after the scrubber
> for this reason, as any water condensed on the sensor membrane will
> affect the measurement. As for flow, the actual flow rate is not as
> critical as its consistency. With zero flow, oxygen diffusion through
> the sensor membrane will reduce the oxygen concentration in the region
> immediately adjacent to the sensor, which will then read erroneously
> (i.e. oxygen diffusion rate through the air becomes a limiting factor).
> You want to have some flow so that the sensor reading accurately
> reflects the gas composition you are trying to measure. Additionally, if
> the gas is dry, flowing it across the sensor membrane can help
> discourage condensation - another plus. If your flow is too fast,
> however, the pressure at the sensor membrane does not accurately reflect
> the pressure of the gas you are trying to measure, so the apparent PPO2
> will be different, again leading to (slightly) erroneous results.
> Ideally, you want just enough flow to continuously refresh the gas at
> the sensor and keep it dry. Using a flow restrictor or some other means
> of controlling the flow rate will ensure that your readings are
> consistent from one measurement to another, which allows you to
> accurately calibrate the sensor against atmospheric air, pure oxygen or
> some other reference at the same pressure as your operating
> measurements. This also allows you to to determine when a sensor is
> starting to go bad.
>
> -Sean
>
> On Wednesday 23 February 2011 11:39:38 you wrote:
>> Hi all,
>> was putting my O2 analyzer together & read a link that I think Jens
>> provided
>> http://www.scubadiver.cc/forums/showthread.php?1272-Design-Construction-
>> Op eration-and-Maintenance-of-an-Oxygen-Analyzer wich states the
>> following...........
>>
>> Essentially all galvanic O2 sensors (such as those listed in the table
>>
>> above) function best with a gas flow around 2-4 liters per minute.
>>
>> Am wondering what other people do with regard to this flow or whether
>> I've bought the wrong thing (El Cheapo O2 analyzer kit) Was thinking of
>> mounting the O2 analyzer in the intake to the CO2 scrubber to get a bit
>> of flow going through it. Regards Alan
>
> ************************************************************************
> ************************************************************************
> ************************************************************************
> The personal submersibles mailing list complies with the US Federal
> CAN-SPAM Act of 2003. Your email address appears in our database
> because either you, or someone you know, requested you receive messages
> from our organization.
>
> If you want to be removed from this mailing list simply click on the
> link below or send a blank email message to:
> removeme-personal_submersibles@psubs.org
>
> Removal of your email address from this mailing list occurs by an
> automated process and should be complete within five minutes of
> our server receiving your request.
>
> PSUBS.ORG
> PO Box 53
> Weare, NH 03281
> 603-529-1100
> ************************************************************************
> ************************************************************************
> ************************************************************************
************************************************************************
************************************************************************
************************************************************************
The personal submersibles mailing list complies with the US Federal
CAN-SPAM Act of 2003. Your email address appears in our database
because either you, or someone you know, requested you receive messages
from our organization.
If you want to be removed from this mailing list simply click on the
link below or send a blank email message to:
removeme-personal_submersibles@psubs.org
Removal of your email address from this mailing list occurs by an
automated process and should be complete within five minutes of
our server receiving your request.
PSUBS.ORG
PO Box 53
Weare, NH 03281
603-529-1100
************************************************************************
************************************************************************
************************************************************************