----- Original Message -----
Sent: Thursday, October 20, 2005 8:51
AM
Subject: Re: [PSUBS-MAILIST] 12 Volt
Solenoids
Bill,
I'm sure your not going to find more bang for
your buck then with regular, off the shelf, lead acid batteries.
And, I know you'll find them in a diameter that will fit in a 12 inch
pipe. What you have to decide is, are you going to find yourself in a
position that is likely to spill acid out of the batteries and are you going
to be able to vent your battery pods every time your charging them? If
spillage isn't a problem and you can vent, go with the deep cycle lead
acid.
I doubt you'll find 24 volt batteries, and if you
do, they won't be cheaper then two 12s. Using two separate 24 volt
circuits is a good idea. You can draw one down to half and switch to the
second, then draw it half way down, and still know you have
reserve. Any battery dealer should be able to tell you how long his
batteries will run your motor at it's rated current draw. Don't rely on
guessing friends.
You'll find that, under water, your hardly ever
going to run your thruster at full power. Even more so, if your in "pea
soup" like water. You just can't see to go that fast. Where you
might use a heavy power draw is surfaced going to and from
a dive site. You have to decide if your going to be towed to a dive
site or maybe be diving close to where you put in at. If so, you'll dive
all day and use the equivalent of an hour or two of total power draw.
Those sealed auto type relays are great for your
application. I rebuilt the side thruster controls for "Persistence"
using them. They're quieter and more reliable then the open type relays
I originally used. McMaster Carr has a good selection of them at a good
price. If you don't have their catalog, do a search for them on the
web.
These are enclosed relays so there is no visible
spark but I still wouldn't put them in a pod with a battery. I'm sure
they aren't rated as explosion proof. Keep in mind that even a battery
in it's normal use isn't explosion proof. Your pod cap should be fixed
in a manner that it's the weakest link in a pod explosion so it can blow off
in a direction not facing you. The concussion of a pod explosion would
be bad enough. It's rare but does happen.
You will need more then one relay if your going
to switch from forward to reverse and maybe to switch from one bank of
batteries to another. The thing to avoid is a situation
where one relay is energized and it's possibility to energize an second
relay reversing the power which will create a dead short across the
batteries.
If you could switch battery banks
mechanically it would be better. Maybe a rotary switch sealed in a
pod. They're made for campers and the like that have two
battery setups. Automotive type places should be able to get them for
you.
You do defiantly need a speed controller.
You can pulse your motors on and off and also, as you said, run them on half
power but if your visibility isn't good, you'll have times when you want to go
real slow. A dead man is a good idea but you could incorporate that in
some other way. I would see if Minkota has a rotary type controller that
will work with your motor or maybe purchase some kind on the net that
will. A rotary controller is really easy to work into a housing with a
waterproof O-ring shaft seal. I
don't think a trigger switch from a drill will do what you want anyway.
First figure out what controller you can find
that will work and you can make water tight. Then you can decide if you
have to go with the 12 - 24 volt controls or not. After that I'll help
you arrange the wiring if you still need.
I think I addressed all your questions. If
I missed something just ask again. If you list the questions, they would
be easier to answer one by one.
Happy parts hunting, Dan H.
----- Original Message -----
Sent: Thursday, October 20, 2005 7:03
AM
Subject: Re: [PSUBS-MAILIST] 12 Volt
Solenoids
Hi Dan.
Thanks for responding. I need the help. Yes,
you are right, I was thinking of using the car solenoids. Are there better
ones to use than those? I have the basic idea of what I want to do and
somewhat how to do it, but
I do not know exactly what amps, volts, etc to
use. I'm not sure I could draw up a clear picture of what I want to do Dan,
I'm not really sure how to do what I want to do to be able to draw a picture
of it Lol!
But generally speaking I was thinking of
this......
I would like to find out if there are better
batteries to use than standard lead acid deep cycle marine batteries that
are not cost prohibitive. I was thinking of using four small 12 volt sea
scooter batteries and connect them in
SEPERATE pairs in series so each pair put out
24 volts. One pair being for backup. But friends have told me my 74lbs
thrust minnkota would eat up the electricity a lot faster than my sea doo
sea scooter does,
and they said those small size batteries
would not last very long at all driving the big minnkota. That makes sense
to me, but I just don't know and am not sure what kind of batteries to get
for sure.
From past threads at psubs, I have heard
members say you cannot beat a regular deep cycle marine battery for cost
compared to some of the newer gel types. Are deep cycle marine batteries
that are 24 volts
and will fit into my 12 inch diameter pvc
battery pod even made or will I have to go with the 12 volt ones? I'm not
really up on types of batteries out there..
First I need to find out if I can purchase 24
volt deep cycle marine batteries that would fit in my 12 in diameter pod. If
I can, I will use two. If not, I will use four 12 volt batteries
and
connect two SEPERATE pairs of them together in
series. That way I will have two 12 volt batteries making 24 volts to use to
begin the dive with, and if they run dry, I will have another
pair just like the first, to come back on. I
would like to have a variable speed control switch if possible, but if a
waterproof one is not available or I can't rig a speciality
tool, explosion proof (sparkless)
variable speed drill switch, to be waterproof,
then I will just use toggle switches that have a rubber boot on the front
and encase the back terminals in a silicon blob for waterproofing. A
variable speed
trigger switch with a reverse setting would be
the ultimate ticket. A trigger switch like that would also act as a "dead
mans" switch, so the switch would not be able to run the motor without
someone holding it down, just like
my sea doo scooter does. Otherwise, I have to
use the toggle switches and that means one position for batteries off,
another position for 12 volts at half speed, another position
for 24 volts at full speed and another position
for reverse. Not the optimum choice and just two speeds. The batteries will
be enclosed in my 12 inch pvc pipe with removable end cap and "O" ring
mounted on the keel.
The solenoid could be in another smaller
pvc pipe seperate from the batteries to make
sure no sparks from the solenoid could possibly ignite any hydrogen from the
batteries. Are there sparkless solenoids available that would
enable me to just put the solenoid into the 12 inch pvc battery pod? I don't know if
I need seperate solenoids for each function of the switches or not. I am not
very versed in electrical hookups but if I had someone explain
exactly
what to do, I could do that. I also would
encase all wire ends in epoxy to preclude any hydrogen from seeping thru the
battery wires to the solenoid compartment.
That's pretty much my rough plan Dan. Sorry for
the encyclopedia. There was no quick way to tell it. I haven't even touched
on whether I should oil fill or air compensate my motor, also whether I
should use BCD bladders
in the bow and stern for buoyancy and trim or
if I should just centrally locate 4 or 6 inch pvc pipes along the upper side
of the sub for buoyancy or even if I should just make the sub always
very slightly buoyant and just use my
personal BCD to change attitude when
submerged. It is complicated by the fact that it is a TWO person
cockpit wetsub but sometimes I may be diving
it alone which would change the center of gravity.
But the buoyancy and motor pressure
equalization questions I will leave for now until I get the batteries and
wiring figured out first. Thanks again for your kind offer of
help.
What do you advise?
Bill.
----- Original Message -----
Sent: Wednesday, October 19, 2005
10:55 PM
Subject: Re: [PSUBS-MAILIST] 12 Volt
Solenoids
Bill,
The main difference in a 12 volt solenoid and
a 24 volt solenoid is the voltage it takes to operate the coil. The
coil has to be operated with the proper voltage. The contacts of the
relay are more current sensitive then voltage sensitive. As long as
your relay current rating is as high or higher then the current
(amps) draw of your motor, use it. I assume your talking about the
can type solenoids like the auto industry uses for car starters.
Correct?
If you send me a pic of what you planning to
do, I may be able to help you come up with some wiring ideas.
Dan H.
----- Original Message -----
Sent: Wednesday, October 19, 2005
4:33 PM
Subject: Re: [PSUBS-MAILIST] U505
gets historically correct paint.
Hi Ray.
I know what you mean. As a diver in Florida
in our mucky gulf, I've gotten used to the "Viz" as we call
visibility,
being less than adequate. There are times I
have been unable to see beyond several feet because of the silty
muck.
I agree with you that the phosphorescent
paint could help inside our subs. I also like John Gaertner's point
about the LED's
and the low voltage light they give. The
higher end dive lights are all going to led's now. I think the best
thing would be to have
both the phosphorescent paint and the
LED's. When it is time to paint my wetsub, I might opt for
phosphorescent yellow paint
so it could be seen better underwater.
Speaking of my wetsub, I am still hoping to get advice on how to hook up
my dash switches
to the solenoid and then to the batteries.
Not sure if I can use a 12 volt solenoid for the 24 volt motor or not.
Still need help in figuring
out how to hook it all up now that I've
mounted the motor. Anyone have advice?
Bill.
----- Original Message -----
Sent: Wednesday, October 19, 2005
1:33 PM
Subject: Re: [PSUBS-MAILIST] U505
gets historically correct paint.
Hi Bill,
The bit about "phosphorescent coat" got
me thinking.
Critical knobs and switches in our PSUB'S
could
benifit from such a coating. I found out during
my
submersible pilot training it can get unexpectedly
dark.
Surprising how dark it gets driving into muck
stirred off the
bottom. Even at only 15 feet down!
Regards,
Ray
---
Akins <lakins1@tampabay.rr.com>
wrote:
> U505 gets the historically correct paint inside
and
> out. Wooden decking gets correct preservative
also.
> Bill.
>
>
http://www.nace.org/nace/content/library/articles/features/uboat.asp
__________________________________
Yahoo! Mail - PC Magazine Editors' Choice 2005
http://mail.yahoo.com
************************************************************************
************************************************************************
************************************************************************
The
personal submersibles mailing list complies with the US
Federal
CAN-SPAM Act of 2003. Your email address appears in
our database
because either you, or someone you know, requested you
receive messages
from our organization.
If you want to be
removed from this mailing list simply click on the
link below or
send a blank email message to:
removeme-personal_submersibles@psubs.org
Removal
of your email address from this mailing list occurs by an
automated
process and should be complete within five minutes of
our server
receiving your request.
PSUBS.ORG
PO Box 311
Weare,
NH
03281
603-529-1100
************************************************************************
************************************************************************
************************************************************************