[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
RE: [PSUBS-MAILIST] wagon style trailer
Jim your e-mail link did not function
Jim,
You have some interesting little projects ! Are you located up in
Kingsberg? I have taken my bees up there for pollination for years, until
recently, now I have them in Paso Robles in the apples.
I have some similar projects !
I like the electric boat motor!
I built a "kanyak" a cross between a Canoe and a kayak
I "attempted" to build a bicycle trailer that is a pusher trailer that has a
briggs and straton 3hp lawn mower engine in it, I started that when gas got
to $4.50/gal. I still have it, I had some gearing problems. It's on hold.
Brian Cox, Ojai,CA
-----Original Message-----
From: owner-personal_submersibles@psubs.org
[mailto:owner-personal_submersibles@psubs.org]On Behalf Of Jim Rudholm
Sent: Thursday, April 01, 2010 10:37 PM
To: personal_submersibles@psubs.org
Subject: Re: [PSUBS-MAILIST] wagon style trailer
Brian,
This link shows the trailer under the L. Francis Herreshoff launch I
built in the '70s.
http://www.psnw.com/~jmrudholm/stiletto.html
The hubs were from one-ton pickups, full floating, with the axles
removed and a heavy clear plastic cover in place. The center was
drilled and tapped 1/8" NPT with a small hole for breathing when on
the road. 30 wt oil was the lube. The axles were 4" pipe dropped in
the center to clear the keel. Eight bolt pattern wheels, 16" tires.
Before launching, the NPT plugs were removed and replaced with tire
valves and hand pumped to five or six psi. This kept the Garlock seals
tight when they reached launch depth, say 5-6'. I never had problems
with water in the lube after this fix. Springs were conventional leaf
with the equalizing link in the center. I kept the hydraulic brakes on
the front axle and had a surge hitch, somewhat more reliable than
electric but not as smooth when towing. I had a half-ton Chevvy for
towing and did a couple of trips to Stockton from the Fresno area. At
47', the boat got attention.
JimR.
On Thu, Apr 1, 2010 at 9:01 PM, Brian Cox
<ojaivalleybeefarm@dslextreme.com> wrote:
> I've been making some progress on my trailer ! ( a necessity this
> juncture ) Since my sub is about 21' long I put the duelies in the back (
> two axils - four wheels) and then I found an old rear end from a Chevy and
> made a pivot plate arrangement which I welded up to a standard trailer
ball
> type hitch. It's very nice because there is absolutely no weight to speak
> of on the ball. This will probably be for just moving around my shop area
> but it could possibly be used for the road. Searching the internet I
found
> some examples of this type of set up - but not many. Since you have two
> pivot points backing up would be challenging. Most "wagon" type trailers
> you see on farms. But I did read some accounts of people who have used
> them. One person said that you could have a "wandering" problem at higher
> speeds.
>
> Brian
>
>
>
>
> ************************************************************************
> ************************************************************************
> ************************************************************************
> The personal submersibles mailing list complies with the US Federal
> CAN-SPAM Act of 2003. Your email address appears in our database
> because either you, or someone you know, requested you receive messages
> from our organization.
>
> If you want to be removed from this mailing list simply click on the
> link below or send a blank email message to:
> removeme-personal_submersibles@psubs.org
>
> Removal of your email address from this mailing list occurs by an
> automated process and should be complete within five minutes of
> our server receiving your request.
>
> PSUBS.ORG
> PO Box 53
> Weare, NH 03281
> 603-529-1100
> ************************************************************************
> ************************************************************************
> ************************************************************************
>
>
************************************************************************
************************************************************************
************************************************************************
The personal submersibles mailing list complies with the US Federal
CAN-SPAM Act of 2003. Your email address appears in our database
because either you, or someone you know, requested you receive messages
from our organization.
If you want to be removed from this mailing list simply click on the
link below or send a blank email message to:
removeme-personal_submersibles@psubs.org
Removal of your email address from this mailing list occurs by an
automated process and should be complete within five minutes of
our server receiving your request.
PSUBS.ORG
PO Box 53
Weare, NH 03281
603-529-1100
************************************************************************
************************************************************************
************************************************************************
************************************************************************
************************************************************************
************************************************************************
The personal submersibles mailing list complies with the US Federal
CAN-SPAM Act of 2003. Your email address appears in our database
because either you, or someone you know, requested you receive messages
from our organization.
If you want to be removed from this mailing list simply click on the
link below or send a blank email message to:
removeme-personal_submersibles@psubs.org
Removal of your email address from this mailing list occurs by an
automated process and should be complete within five minutes of
our server receiving your request.
PSUBS.ORG
PO Box 53
Weare, NH 03281
603-529-1100
************************************************************************
************************************************************************
************************************************************************