Dean,
In general the idea is to use a large
diameter prop turning at a slow speed, it'll produce more thrust and be much
more efficient. According to Dave Gerr in "The propeller handbook", the ideal
is for the prop diameter to be one third the beam of the vessel. To give you an idea how much of a difference diameter
makes, I'll quantify with an example: 1 HP at the shaft could produce 39.5 lbs
of thrust with a 6" prop, or 62.7 lbs with a 12" prop. Does it really
have to be direct drive, or could you use say belt drive to slow down the
rpms?
Just to recap the design steps I went
through to answer this same question on my own project, they
were:
1) Determine largest diameter prop I can
fit. In my case the limiting factors were interference with the surface,
and the desired draft. My prop ended up being 16".
2) Next, calculate the most efficient RPM.
You can get it from:
rpm^0.6 = (632.7 * SHP^0.2)/D
where
SHP = shaft horse power
D = prop diameter
In my case, I estimated SHP to be 90% of
the motor's rated continuous power, which led to 652 rpm.
3) Estimate propeller slip. Your prop
isn't slicing through a solid, so it'll slip. How much depends largely on how
streamlined the boat is. The normal practice in ship design is to base this
number on comparison to similar vessels -- not easy to do for a sub, where I
had no data at all. For a displacement hull surface vessel a normal value
might be 45%. I increased that to 60% slip, because a PSUB is far less
hydrodynamic than your typical boat. However my value is a total
guesstimate.
4) Estimate the vessel's theoretical
speed.
Speed in knots = [10.665 /
(Displacement in lbs / SHP)^0.3]*(waterline length in feet)^0.5
Translate to mph multiplying by
1.15
In my example, I get 5.68 mph
5) Calculate the ideal propeller
pitch
Pitch in inches = mph * 1056 / (rpm * (100
- % slip)/100)
In my case, pitch = 22.9"
Now, because I'm planning to use a Kort
nozzle, I reduced the pitch quite significantly, to 18. Then I went on eBay,
and found a Michigan Prop 16 x 18. I can't remember how much it cost me, I got
it a while back -- but it was probably small change compared to what they cost
new. Another detail, it's what they call a "cupped" prop which refers to the
shape of the blades. Cupped are most efficient for slow speeds, so that's
an added bonus.
I realize several parameters are
estimates. My objective is to get into the ballpark of the correct values, and
I do fully expect to play around with different pulley combinations to
fine tune shaft speed.
Hope that helps.
Alec
The contents
of this e-mail are intended for the named addressee only. It contains
information that may be confidential. Unless you are the named addressee or an
authorized designee, you may not copy or use it, or disclose it to anyone
else. If you received it in error please notify us immediately and then
destroy it.
From: owner-personal_submersibles@psubs.org
[mailto:owner-personal_submersibles@psubs.org] On Behalf Of
Recon1st@aol.com
Sent: Sunday, February 08, 2009
14:08
To: personal_submersibles@psubs.org
Subject:
[PSUBS-MAILIST] buying a propeller
I am in need of choosing a propeller.
Any suggestions on what to consider? cost is for sure a
factor.
I am not gear reducing at this time so I am going to be in
the
1500 rpm range. I will be kicking up to 12hp and should have a
range
between 1 and 2000 rpm.
My overall dry weight should be about 6000lb
Any help greatly appreciated.
Dean
Who's never won? Biggest
Grammy Award surprises of all time on AOL Music.