Hi Chad,
I understand more what you are talking
about.
The problems I see with your design is that the
flat separator from the trim to the surface tank won't hold the pressure since 1
system will be at ambient (surface) and the other will be 1atm when you close
the bottom valve. the trim tank will receive the exact same pressure as your
hull will. you need cylinder shape trim tank to support pressure.
second problem. Free surface. If your trim tanks
are half full, the water will try to move foward or backward then changing the
angle of the sub. The more it tilt, the more the water go forward, you end
up with an upright sub that you can't blow the ballast.... very bad. You need
separators in the tank. Do a search in the archive. This problem have been
addressed many times and explained by more qualified people then
me.
I can't help you with view port as my sub is an
ambient sub. Again, I would recommend searching the archives. You will find alot
of helpfull hints in there. The bubsy book (on-line now) can help you
also.
Hope it help.
Pierre Poulin
----- Original Message -----
Sent: Monday, September 04, 2006 7:55
AM
Subject: Re: [PSUBS-MAILIST] new hull
design
so are you saying use the ambiant tank for trim. I was thinking four trim
tanks and four four surface tanks that way I can trim at four points before
the dive to obtain neutral bouyancy and ballance the boat out. as for the
piping I was trying to do away with alot of external piping. not for any real
resone other than I don't want a bunch of external lines and pipes. I'm not
sure what you mean about deviding the two systems? the trim tanks will have a
drain valve that can be closed and the main surface tanks will vent out the
bottom. air will be inroduced to the tanks from the top of each. once the trim
tanks are set for the load the drain valve is closed and to surface all that
is needed is to fill or flood the main tanks to surface and dive. I was
attemting to streamline the boat also making it opperate more like an attack
sub with dive planes and a joystick control for the rear rudders so as to
operate like a sport sub or aircraft controls. here is a concept of line !
placement. and your oppinion on rectangular view ports would be? also is a
concept drawing for an earlier design based on the flying sub. the top one was
a weight trim design and the bottom one is a trim tank design. of coarse the
tanks would have to be changed top to bottom but I have abandoned this idea
for the other. thankfully yours, Chad Beller east
tx
-----Original
Message----- From: poulin.carrier@videotron.ca To:
personal_submersibles@psubs.org Sent: Mon, 4 Sep 2006 6:25 AM Subject:
Re: [PSUBS-MAILIST] new hull design
Hello unnammed stranger,
A normal ballast system have 2 systems (like
yours) exept that one system is ambient (for surface) and the other system is
1atm (trim) so, as you said, the boyancy won't change as you go
deeper.
When I look at your system I don't see why you
devide your 2 systems since they will work the same way. I think it would work
the same if you only had 1 ambient system.
I also don't see how it could be simplier for the
piping.
Pierre Poulin
-----
Original Message -----
Sent:
Monday, September 04, 2006 2:42 AM
Subject:
[PSUBS-MAILIST] new hull design
all this talk about getting back to subs but everyone still
seems to be arguing over issues. I was waiting for a fist fight at the end
of this pissing contest then we can all hose the testosterone off the decks
and go on eh. I'm just a newbie so don't mind my little joke. I did have
some ques regarding a new design I am trying to come up with to minimize
exterior piping and make lines and valving simpler inside the hull. my trim
tanks will be a closed sys and I am not sure if this is necicary or not. I
was concerned with the air in my trim tanks loosing mass as I drive
deeper if I leave them ambiant which would cause my sub to become neg
boyant at depth. The other concern is that if the trim tanks are a closed
sys is the wall seperating the main tanks from the trim tanks need to be
reinforced? as for the other ques that I have had earlier I found a place I
should have known to look for affordable parts and sealed rotating
assemblies. grainger.com has ! a wide variety of parts for those interested
in looking. they also have a few co2 and o2 meters avalible and a wide
variety of hydrolic as well as peunamatic parts for fabrication.
any
thoughts on rectangular port view holes instead of round.
|