[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: RE: [PSUBS-MAILIST] protecting Aluminum parts
Are you using 7075 in the marine industry? It would seem to be excessively acceptable to corrosion.
bob duncan
jbarlow@bjservices.ca wrote:
Getting the parts Hard Coat anodized provides aprox 60 HRc surface of
Aluminum oxide (similar to its natural oxide) but is quite impervious to
scratches ect. It also makes the surface not conductive thus preventing
galvanic corrosion. I believe the correct call out is "Type III Hard Coat
Anodize" I usually get 6061-T6 parts anodized, but have anodized 5052 and
7075 grades as well.
My 2¢.
Jay.
drewacard@charter.net
Sent by: To:
owner-personal_submersible cc:
s@psubs.org Subject: Re: RE: [PSUBS-MAILIST] protecting aluminum parts
2004-01-07 07:47
Please respond to
personal_submersibles
6061 is a marine grade if it is harden to T6 hardness it will form a thin
oxide layer on it own. This thin layer will protect the metal from
salt
water if it is not scratched. However I would coat the ring with a clear
epoxy or polyester paint to prevent galvanic corrosion
just my 2 cents
Andy Jensen
From: "Alec Smyth"
Date: 2004/01/06 Tue AM 09:52:50 CST
To:
Subject: RE: [PSUBS-MAILIST] protecting aluminum parts
Its 6061.
Thanks,
Alec
-----Original Message-----
From: drewacard@charter.net [mailto:drewacard@charter.net]
Sent: Tuesday, January 06, 2004 9:50 AM
To: personal_submersibles@psubs.org
Subject: Re: [PSUBS-MAILIST] protecting aluminum parts
What grade of Aluminum is it?
From: "Alec Smyth"
Date: 2004/01/06 Tue AM 08:14:08 CST
To:
Subject: [PSUBS-MAILIST] protecting aluminum parts
One of the relatively more expensive parts of my sub is a massive
aluminum ring that seats the acrylic bow dome and
opens and closes as a
hatch. I know it will form an electrolytic pair with other metals on the
boat, and thus corrode. But I have a practical question... given the sub
is likely to be in the water only an hour or two, and get washed down
with fresh water afterwards, is the need to protect the aluminum real,
or would it only be an issue with longer exposures?
I'd be much obliged if anyone with unprotected Al parts on their sub
share their experience on this. Anoziding looks nice but on a part this
size would be very expensive (extrapolating from what I've paid for much
smaller parts, probably in the order of $500). I'm not sure whether to:
a) Do nothing
b) Use a zinc anode near the hatch
c) Paint
d) Anodize
Just as background information, I don't have any other metals in direct
contact with the Al on the wet side, except for the hatch seat, but that
should be pretty well protected as it has 4 coats of Gluvit epoxy
base
and 5 coats of epoxy paint. On the dry side, the ring is mechanically
connected to bars that go through linear bearings attached to the hull.
This does connect it electrically to the hull as well.
Thanks,
Alec
*********************************************
* This e-mail was virus scanned upon receipt.
*********************************************
******************************************
* This e-mail was virus scanned when sent.
******************************************
Two guiding principles govern Israel Naval Commando doctrine:
1.Every defense system is vulnerable.
2.The enemy can deal with weapons and operational methods that are known; for that reason, naval commandos use imagination, daring and initiative, to create situations which cannot be anticipated.
Do you Yahoo!?
Yahoo! Hotjobs: Enter the "Signing Bonus" Sweepstakes