Thanks Hugh,
Greg
--- On Sat, 5/15/10, Hugh Fulton <hc.fulton@gmail.com> wrote:
From: Hugh Fulton <hc.fulton@gmail.com>
Subject: RE: [PSUBS-MAILIST] MBT vent valves
To: personal_submersibles@psubs.org
Date: Saturday, May 15, 2010, 5:34 PM
Greg I will put the drawings together and email off line tomorrow.
Regards,
Hugh
From: owner-personal_submersibles@psubs.org [mailto:owner-personal_submersibles@psubs.org] On Behalf Of greg cottrell
Sent: Wednesday, 12 May 2010 12:44 p.m.
To: personal_submersibles@psubs.org
Subject: RE: [PSUBS-MAILIST] MBT vent valves
I'd be interested in hearing about all of them actually. In answer to your question about size, if it were a ball valve it would be 1" full open.
--- On Tue, 5/11/10, Hugh Fulton <hc.fulton@gmail.com> wrote:
From: Hugh Fulton <hc.fulton@gmail.com>
Subject: RE: [PSUBS-MAILIST] MBT vent valves
To: personal_submersibles@psubs.org
Date: Tuesday, May 11, 2010, 5:05 PM
Hi Greg, what size valve are you looking for.
We are doing 3 types. 2 of them with bimba Cylinders and one is integral.
One is vent come relief valve. Hugh
From: owner-personal_submersibles@psubs.org [mailto:owner-personal_submersibles@psubs.org] On Behalf Of greg cottrell
Sent: Wednesday, 12 May 2010 5:25 a.m.
To: personal_submersibles@psubs.org
Subject: [PSUBS-MAILIST] MBT vent valves
Has anyone found a good remotely operated (pneumatic?) valve that would be well suited as a MBT vent? Thanks.
--- On Sat, 5/8/10, Cliff Redus <cliffordredus@sbcglobal.net> wrote:
From: Cliff Redus <cliffordredus@sbcglobal.net>
Subject: Re: [PSUBS-MAILIST] pressure hull sizing
To: personal_submersibles@psubs.org
Date: Saturday, May 8, 2010, 12:53 PM
Sorry for the delay. I have been busy of late in the real world. My boat pressure hull is 30". As I was going for a low drag profile, this has worked fine. If I had to do it again with the same design objectives, I would again use a 30" hull but would have external stiffeners, not internal to give more room and make maintenance easier.
Cliff
From: "Fritz, Benjamin T AT1 CNATTU, JACKSONVILLE" <benjamin.fritz@navy.mil>
To: personal_submersibles@psubs.org
Sent: Thu, May 6, 2010 12:09:14 PM
Subject: [PSUBS-MAILIST] pressure hull sizing
Hey guys,
I was looking at my designs for my sub and noticed that the interior size is lacking in open volume when all the internals are installed. Right now its all theoretical placement using the dimensions of the components. My hull diameter is planned at 30", at this point I don't think it will be enough...
Of the members of the K-Sub mafia, what size hull is more common for construction? Cliff, what size hull did you use for the R-300? |
__________ Information from ESET NOD32 Antivirus, version of virus signature database 5103 (20100510) __________
The message was checked by ESET NOD32 Antivirus.
__________ Information from ESET NOD32 Antivirus, version of virus signature database 5103 (20100510) __________
The message was checked by ESET NOD32 Antivirus.
http://www.eset.com
|
__________ Information from ESET NOD32 Antivirus, version of virus signature database 5106 (20100511) __________
The message was checked by ESET NOD32 Antivirus.
http://www.eset.com
__________ Information from ESET NOD32 Antivirus, version of virus signature database 5117 (20100515) __________
The message was checked by ESET NOD32 Antivirus.
http://www.eset.com
|