-----Original Message-----
From: Greg Cottrell <greg@precisionplastics.com>
To: personal_submersibles@psubs.org
Sent: Mon, May 3, 2010 10:20 am
Subject: [PSUBS-MAILIST] oil filled/ another method
There is another way to modify a Minn Kota without taking it apart. This
method avoids damage to the housing and filings in the motor.
(1) Remove the "composite shaft"
(2) With the shaft on a bench, just above the threads where it screws into
the motor, install a pair of barb fittings on each side of the shaft.
(3) Approximately 3" further up the shaft, drill a .250" hole.
(4) Strip a 1" section of insulation off each wire. Stager the two exposed
sections (red 4" from motor, black 5" from motor)
(5) Solder these sections hard.
(6) Re-insulated these sections using a Devcon Mark 5 "plastic welder" gun
and Devcon plastic welder # 14320. Cover both the metal wire and the
insulation. Make sure the wires will fit back in the shaft after they
harden.
(7) Re-install the shaft on the motor. Use pipe dope on the threads.
(8) Lay the motor/ shaft down on the bench. Plug the barb fittings so air
cannot escape. Using the 3M plastic welder, inject plastic weld into the
.250 hole, creating a "plug" around the wires and also sealing the shaft. It
should cover the entire splice area. Check barb fittings are still clear.
(9) After the plug sets up, stand the motor shaft up and fill a few more
inches of shaft with 2-part liquid urethane.
(10) Attach hose to one of the barb fittings. Select a clear hose that stays
flexible in cold water. This will form a "loop" after filling.
(11) Fill motor with light mineral type oil that won't hurt plastic or
rubber.
(12) Attach the end of loop to the other barb fitting.
(14) submerge in water and test.
Greg Cottrell
Project Manager
greg@precisionplastics.com
http://www.precisionplastics.com
P please consider the environment before printing this email
-----Original Message-----
From: owner-personal_submersibles@psubs.org
[mailto:owner-personal_submersibles@psubs.org] On Behalf Of Jon Wallace
Sent: Monday, May 03, 2010 8:47 AM
To: personal_submersibles@psubs.org
Subject: [PSUBS-MAILIST] Oil Compensate Motor
Here are the instructions that were posted by Alec Smyth regarding oil
compensation of a trolling motor.
http://www.psubs.org/mlist/archive/0906/msg00164.html
The advanced features of the web site search engine are your friend
here. I searched for "oil compensate" in the "whole document" and found
this thread on the third page of results. When I changed the search to
look at the "Title" only, it was the first and only result.
Jon
************************************************************************
************************************************************************
************************************************************************
The personal submersibles mailing list complies with the US Federal
CAN-SPAM Act of 2003. Your email address appears in our database
because either you, or someone you know, requested you receive messages
from our organization.
If you want to be removed from this mailing list simply click on the
link below or send a blank email message to:
removeme-personal_submersibles@psubs.org
Removal of your email address from this mailing list occurs by an
automated process and should be complete within five minutes of
our server receiving your request.
PSUBS.ORG
PO Box 53
Weare, NH 03281
603-529-1100
************************************************************************
************************************************************************
************************************************************************
************************************************************************
************************************************************************
************************************************************************
The personal submersibles mailing list complies with the US Federal
CAN-SPAM Act of 2003. Your email address appears in our database
because either you, or someone you know, requested you receive messages
from our organization.
If you want to be removed from this mailing list simply click on the
link below or send a blank email message to:
removeme-personal_submersibles@psubs.org
Removal of your email address from this mailing list occurs by an
automated process and should be complete within five minutes of
our server receiving your request.
PSUBS.ORG
PO Box 53
Weare, NH 03281
603-529-1100
************************************************************************
************************************************************************
************************************************************************