I use the magnetic drives
on all of my dpv's. Nothing works better. The hardest part is that you have to
maintain pressure on the shaft from the prop end. It's a semi-easy fix. The
prop shroud has a nut in the center, that aligns with the center of the prop.
I tighten to maintain a slight pressure on the ceramic disk in the bottom of
the magnet cup. I use ceramic shafts for the prop magnet to ride in, and the
nut on the shroud holds it all together. If you don't put the pressure on it,
it wobbles badly in a turn but works almost flawlessly in a stratight line, It
always fixes itself, and the wobble is more disheartening then
disfunctional. Some I use as pullers and some as pushers. The pusher align
better as the magnet is being forced into the bottom of the cup. Great clutch,
or not, dependant on the size of the magnets you use. I can use smaller ones
and get a good slow start and then the fields catch, and I have a couple of
huge ones that take! about 30 ftlbs to knock out of field. It's the reason I
lurk here. I build dpv's and not subs. All of them, about 6 right now,
are magdrive. With the mag drive you get to use any motor you like as all is
sealed and there's no shaft bearing/seal. I have a couple of favorite motors.
You can use geared motors if you like. I have one that has an upgraded motor
from one of those stupid scooters, and it drives through a ryobi 18volt gear
reduced cordless drill head. Great power and pretty tiny overall package. Hooks
right to my scuba tank....
Barkmann <barkmann@jerseymail.co.uk>
wrote:
Sorry,
should read "Magnetic Clutch"
----- Original Message -----
From: "Barkmann"
To:
Sent: Thursday, December 22, 2005 10:09 PM
Subject: Re: [PSUBS-MAILIST] Good source for deep use motors?
> Just a thought, has anyone ever looked into the possibility of using a
> magnetic clutcc (so that there is no through hull shaft sealing to worry
> about).
>
> I must admit, Ive been thinking about this idea as a possibility in my own
> design.
>
> Best regards,
>
> Jack
>
> ----- Original Message -----
> From: "Stockton Rush"
> To:
> Sent: Thursday, December 22, 2005 5:51 PM
> Subject: RE: [PSUBS-MAILIST] Good source for deep use motors?
>
>
> > I am using MinnKota Edrive motors (48VDC, 2Hp) on my K-350 with small
> > ambient compensation reservoirs. The MinnKota engineer I spoke with
said
> > they have been used to 100 ft, and can go deeper, but the shaft seals
> might
> > start to bind at greater depths and reduce performance. The units are>
> extremely stout.
> >
> > Stockton
> >
> >
> > From: Robert Ossian
> > Reply-To: personal_submersibles@psubs.org
> > To: personal_submersibles@psubs.org
> > Subject: [PSUBS-MAILIST] Good source for deep use motors?
> > Date: Thu, 22 Dec 2005 09:30:59 -0800 (PST)
> >
> > I'm trying to find some good (and high performance)
> > motors capable of reaching 250 feet without too many
> > modifications.
> >
> > Anyone know of any good sources/suppliers?
> >
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Tired of spam? Yahoo! Mail has the best spam protection around
> > http://mail.yahoo.com
> >
> >
> >
> >
************************************************************************
> > ************************************************************************
> >
************************************************************************
> > The personal submersibles mailing list complies with the US Federal
> > CAN-SPAM Act of 2003. Your email address appears in our database
> > because either you, or someone you know, requested you receive
messages
> > from our organization.
> >
> > If you want to be removed from this mailing list simply click on the
> > link below or send a blank email message to:
> > removeme-personal_submersibles@psubs.org
> >
> > Removal of your email address from this mailing list occurs by an
> > automated process and should be complete within five minutes of
> > our server receiving your request.
> >
> > PSUBS.ORG
> > PO Box 311
> > Weare, NH 03281
> > 603-529-1100
> &g! t; ************************************************************************
> >
************************************************************************
> >
************************************************************************
> >
> >
> >
> >
> >
> > ************************************************************************
> >
************************************************************************
> >
************************************************************************
> > The personal submersibles mailing list complies with the US Federal
> > CAN-SPAM Act of 2003. Your email address appears in our database
> > because either you, or someone you know, requested you receive
messages
> > from our organization.
> >
> > If you want to be removed from this mailing list simply click on the
> > link below or send a blank email! message to:
> > removeme-personal_submersibles@psubs.org
> >
> > Removal of your email address from this mailing list occurs by an
> > automated process and should be complete within five minutes of
> > our server receiving your request.
> >
> > PSUBS.ORG
> > PO Box 311
> > Weare, NH 03281
> > 603-529-1100
> >
************************************************************************
> > ************************************************************************
> >
************************************************************************
> >
> >
>
************************************************************************
************************************************************************
************************************************************************
The personal submersibles mailing list complies with th! e US Federal
CAN-SPAM Act of 2003. Your email address appears in our database
because either you, or someone you know, requested you receive messages
from our organization.
If you want to be removed from this mailing list simply click on the
link below or send a blank email message to:
removeme-personal_submersibles@psubs.org
Removal of your email address from this mailing list occurs by an
automated process and should be complete within five minutes of
our server receiving your request.
PSUBS.ORG
PO Box 311
Weare, NH 03281
603-529-1100
************************************************************************
************************************************************************
************************************************************************