RE: RE: [PSUBS-MAILIST] Minn Kota Motors

[Brent Shaw <drydivenz@yahoo.com>]

Graham, I've just had shifts made to fit to my motors
and the thread is 1 1/8 and 18 thread per inch

--- Graham K <cryogenicz@dsl-only.net> wrote:
> I called minn kota, they told me it was 1-1/8 thread
> pitch was 18...
> 
> so...
> 
> -----Original Message-----
> From: owner-personal_submersibles@psubs.org
> [mailto:owner-personal_submersibles@psubs.org]On
> Behalf Of
> rjune@fuse.net
> Sent: Monday, July 01, 2002 5:43 AM
> To: personal_submersibles@psubs.org
> Subject: RE: RE: [PSUBS-MAILIST] Minn Kota Motors
> 
> 
> Unless it has changed ... last time I checked it was
> 1-20 UNEF (1", thread pitch of 20, Unified National
> Extra Fine,
> Minor Diamiter = .9459)
> 
> Roger
> >
> > From: "Graham K" <cryogenicz@dsl-only.net>
> > Date: 2002/06/28 Fri PM 05:07:46 EDT
> > To: <personal_submersibles@psubs.org>
> > Subject: RE: RE: [PSUBS-MAILIST] Minn Kota Motors
> >
> > hey, what size is that hole on the minn kota motor
> shaft, I sized it at
> > 1-1/8 thread pitch 18
> >
> > is this correct?
> >
> > Where can I get a plug to fill the hole?
> >
> > -GK
> >
> > -----Original Message-----
> > From: owner-personal_submersibles@psubs.org
> > [mailto:owner-personal_submersibles@psubs.org]On
> Behalf Of
> > rjune@fuse.net
> > Sent: Friday, June 28, 2002 1:17 PM
> > To: personal_submersibles@psubs.org
> > Subject: Re: RE: [PSUBS-MAILIST] Minn Kota Motors
> >
> >
> > I sell the MotorGuide lower units
> > already modified for use down to 300 ft.
> > and with a two year warrantee
> >
> > Roger
> > REJ & Co.
> > rjune@fuse.net
> >
> > >
> > > From: Alec Smyth <Asmyth@changepoint.com>
> > > Date: 2002/06/28 Fri PM 02:43:37 EDT
> > > To: "'personal_submersibles@psubs.org'"
> <personal_submersibles@psubs.org>
> > > Subject: RE: [PSUBS-MAILIST] Minn Kota Motors
> > >
> > > If you check the archives you'll find people who
> sell Minnkota lowers. I
> > > bought some myself but it was ages ago, and I
> don't have the vendor's
> > > information handy here at the office. But he was
> a Minnkota dealer who
> > sold
> > > me only the specific parts I needed, and way
> cheaper than purchasing the
> > > whole motor.
> > >
> > > rgds,
> > >
> > > Alec
> > >
> > > -----Original Message-----
> > > From: papakuk@cs.com [mailto:papakuk@cs.com]
> > > Sent: Friday, June 28, 2002 2:16 PM
> > > To: personal_submersibles@psubs.org
> > > Subject: RE: [PSUBS-MAILIST] Minn Kota Motors
> > >
> > >
> > > Unfortunately the rule of Mass Production rules.
> Ii called MinnKota once
> > > about buying the lower unit and it cost more
> than the whole kit and
> > > caboodle. Kind of like buying car parts.
> > >
> > > By the eay, I think Endura motors can be found
> for around $99. If anyone
> > is
> > > interested I will find an address.
> > >
> > > Ron <ronleonard@shaw.ca> wrote:
> > >
> > > >You also wouldn't be paying for parts you are
> going to throw away.
> > > >Ron
> > > >
> > > >
> > > >-----Original Message-----
> > > >From: owner-personal_submersibles@psubs.org
> > > >[mailto:owner-personal_submersibles@psubs.org]
> On Behalf Of Herve
> > > >Sent: Friday, June 28, 2002 6:33 AM
> > > >To: personal_submersibles@psubs.org
> > > >Subject: Re: [PSUBS-MAILIST] Minn Kota Motors
> > > >
> > > >
> > > >You know if you purchased only the "lower
> unit", you would not have
> that
> > > >trouble removing the pole. Herve
> > > >----- Original Message -----
> > > >From: "Graham K" <cryogenicz@dsl-only.net>
> > > >To: <personal_submersibles@psubs.org>
> > > >Sent: Thursday, June 27, 2002 11:12 PM
> > > >Subject: [PSUBS-MAILIST] Minn Kota Motors
> > > >
> > > >
> > > >> I'm Removing the composite poles from the
> motors, and I'll tell you
> > > >> this,
> > > >IT
> > > >> SUCKS! The composite poles are made of
> fiberglass and when you chip
> it
> > > >
> > > >> out of the hole, the fiberglass gets
> everywhere.. and it gets into
> > > >> your shin
> > > >and
> > > >> Itches worse than any insulation fiberglass I
> have ever felt. But!!!
> I
> > > >
> > > >> got it all out, and they look great... I just
> pretty much followed
> > > >> Carl's instructions, and I cut the composite
> off at about 3 inches
> > > >> from the base
> > > >of
> > > >> the hole, and then took a 2 pound sledge and
> hammered the hell out of
> > > >> the end until it was all mashed up. Then I
> took a flat head screw
> > > >> driver & a regular hammer and chiseled it out
> of the base, and got it
> > > >> all out. Looks great, all I need to do is get
> a Tap and clean out the
> > > >> threads.
> > > >>
> > > >>
> > > >> Regards,
> > > >>
> > > >> Graham Kuberski
> > > >>
> > > >>
> > > >
> > > >
> > > >
> > >
> >
> > Roger June
> > REJ and Company
> > rjune@fuse.net
> > 513-300-1189
> >
> >
> >
> 
> Roger June
> REJ and Company
> rjune@fuse.net
> 513-300-1189
> 
> 


__________________________________________________
Do You Yahoo!?
Yahoo! - Official partner of 2002 FIFA World Cup
http://fifaworldcup.yahoo.com