[PSUBS-MAILIST] boring tool

[Rick Patton via Personal_Submersibles]

Hank,

I have a Bosch mag drill and I love it! They do turn a slow rpm but not an
expert in this field though I have drilled threw 1" plate and it goes threw
like cutting butter. Contact Bosch and they can tell you. The only draw
back to going that route is that not sure if you can rent one and they
aren't cheap to buy plus if they do make a 6" bit, it's gonna set you back
a pretty penny! good luck.
Rick

On Mon, Nov 27, 2017 at 2:56 AM, hank pronk via Personal_Submersibles <
personal_submersibles at psubs.org> wrote:

> Rick, I thought about a Mag drill, but I was thinking about taking my
> small milling machine apart and making a mount on the sphere.  A mag drill
> could be adapted easier because I could just tack weld a flat plate to the
> hull for it to sit on.   I have never used a mag drill and don't know how
> slow they can turn?  I figure I will have to turn something pretty slow.
> Steve, I don't know if I can cut it out with a milling bit, I have very
> little experience with this idea.  I could cut it out small with a torch
> using a circle guide also.  I hate machining torch cut pieces because they
> tent to surface harden.  I suppose I could grind the hard surface off
> first.   I am looking for a easy clean way to do this, before I jump in and
> do it the hard way.
> My goal in to put two small ports in Elementary 3000 without welding them
> in.  I will machine two holes in the hull and then machine two conical port
> frames to fit the hull perfectly and will be retained from the inside of
> the hull.
> Any clever ideas to achieve this would be appreciated.
> Hank
>
>
> On Sunday, November 26, 2017, 11:16:30 PM MST, Stephen Fordyce via
> Personal_Submersibles <personal_submersibles at psubs.org> wrote:
>
>
> Hi Hank,
> You could probably get away with using a holesaw - a one-piece one design
> for cutting metal, not the adjustable ones for cutting wood.  It would take
> a while and need lots of coolant and force, but I think it would be quite
> doable (I've seen big ones used on thick steel before).  The big ones
> aren't cheap though.
>
> Or couldn't you just mill out the circle with a smaller milling bit, so
> that you end up with a disc that drops out when you finish the cut?
>
> Cheers,
> Steve
>
> On Mon, Nov 27, 2017 at 4:17 PM, Rick Patton via Personal_Submersibles <
> personal_submersibles at psubs.org> wrote:
>
> Hank,
> Have you checked into a mag drill yet?
> Rick
>
> On Sun, Nov 26, 2017 at 1:49 PM hank pronk via Personal_Submersibles <personal_submersibles at psubs.
> org <personal_submersibles at psubs.org>> wrote:
>
> Hi All,
> Is there such a tool that can bore a 6 inch dia hole in 1 inch thick
> plate.  Some sort of milling machine tool, it needs to machine a precision
> hole.
> Hank
> ______________________________ _________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs. org <Personal_Submersibles at psubs.org>
> http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles
> <http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles>
>
>
> ______________________________ _________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs. org <Personal_Submersibles at psubs.org>
> http://www.psubs.org/mailman/ listinfo.cgi/personal_ submersibles
> <http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles>
>
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
> _______________________________________________
> Personal_Submersibles mailing list
> Personal_Submersibles at psubs.org
> http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20171127/53b9129d/attachment.html>