[PSUBS-MAILIST] Manipulator arm

Fri May 30 12:05:50 EDT 2014

Scott,
The joy sticks are mounted so I can reach them easily while looking out the ports.  They are wired to operate the same as a bob-cat excavator.  You could hop right in and go to work.
Hank--------------------------------------------
On Fri, 5/30/14, swaters via Personal_Submersibles <personal_submersibles at psubs.org> wrote:

 Subject: Re: [PSUBS-MAILIST] Manipulator arm
 To: "Personal Submersibles General Discussion" <personal_submersibles at psubs.org>
 Received: Friday, May 30, 2014, 11:40 AM

 Hank,Do
 you have any detailed pictures of the controller for the
 manipulator? How is the controller arranged in the
 submarine?Thanks,Scott
 Waters

 Sent
 from my U.S. Cellular© Smartphone 
 hank pronk via Personal_Submersibles
 <personal_submersibles at psubs.org> wrote:
 Hugh,
 The wrist movement on Gamma is about 345 degrees and is
 accomplished with a single vane motor so to speak.  I
 did not build that arm, so I am not sure where that part
 came from.  I think it is a custom piece.  
 Outside the wrist and hand, copying that arm is the way to
 go for psubbers.  That arm is very light and robust,
 also simple to build.  The hand could be replicated
 with two small 1 in bore cylinders instead of the way it is
 now.  Right now the hand and wrist are quite
 complicated to build for the average guy on a budget. 

 Hank
 --------------------------------------------
 On Thu, 5/29/14, Hugh Fulton via Personal_Submersibles
 <personal_submersibles at psubs.org> wrote:

  Subject: Re: [PSUBS-MAILIST] Manipulator arm
  To: "'Personal Submersibles General
 Discussion'"
 <personal_submersibles at psubs.org>
  Received: Thursday, May 29, 2014, 7:09 PM

  Thanks Hank, great info. And the arms
  on your project page look pretty
  smart.  What was the wrist movement and how is that
  accomplished.  Was it
  continual rotation or 180 degree.
  I see that Hydrolek uses a gerotor.  We need a Psubs
  project to do a manip.
  Maybe a good subject for the next meeting. 
  Cheers,  Hugh 

  -----Original Message-----
  From: Personal_Submersibles
 [mailto:personal_submersibles-bounces at psubs.org]
  On Behalf Of hank pronk via Personal_Submersibles
  Sent: Friday, 30 May 2014 9:25 a.m.
  To: Personal Submersibles General Discussion
  Subject: Re: [PSUBS-MAILIST] Manipulator arm

  Hi Hugh,
  The convertible top pumps are about the same size as a
 wind
  shield wiper
  motor.  They are quite small actually.  I would
  say the motor is about 2.5in
  dia and 6in tall.  They develop 1,000 psi, at least
 the
  one I tested did.  I
  have only used GM pumps, but I am sure they are all the
 same
  more less. Also
  I have had good success with a common snow plow hyd
  pump.  You will need a
  hyd valve bank if you use the snow plow pump.  The
  beauty of a top pump is
  that you do not need a valve bank. Gamma has an aircraft
  pump that according
  to the maintenance records works best at 1,100 psi when at
  max depth of
  1,000 feet.
  That means you only need about 650psi above bottom for the
  arm to work.  I
  have the pressure set at 500 psi for shop testing and it
  seems good already
  at that pressure.  

  Hank
  --------------------------------------------
  On Thu, 5/29/14, Hugh Fulton via Personal_Submersibles
  <personal_submersibles at psubs.org>
  wrote:

   Subject: Re: [PSUBS-MAILIST] Manipulator arm
   To: "'Personal Submersibles General
 Discussion'"
  <personal_submersibles at psubs.org>
   Received: Thursday, May 29, 2014, 4:36 PM

   Hank,
   That seems like very good advice.  I am wanting
 to do
  a  manipulator but
  need  to get some idea of what lifting or forces are
  required.
   What are the pumps you have found to work
 best. 
  What  pressure do they
  develop? I had no idea what a top pump was so googled it
  and  came up with
  breast pumps!! I didn't want to make a tit of myself
  so  chased down some
  more and found that they are for convertible cars. They
  look  a bit on the
  large side diameter wise.  Any brand best? 
 Cheers, 
  Hugh 

   -----Original Message-----
   From: Personal_Submersibles
  [mailto:personal_submersibles-bounces at psubs.org]
   On Behalf Of hank pronk via Personal_Submersibles
   Sent: Friday, 30 May 2014 12:21 a.m.
   To: Personal Submersibles General Discussion
   Subject: Re: [PSUBS-MAILIST] Manipulator arm

   Scott,
   No matter how you do it, a manipulator will cost
 some
  of  money.  I have
  made  many and the tendency seems to be, to try and
  make them  strong to
  lift a  lot.  Well first off, I think it was
 Vance
  that said it  best.  A
  manipulator  is for manipulating not lifting. 
 With
  that in mind,  large
  components are  not needed.  Simple air cylinders
 from
  ebay are  all that is
  needed.  A 2in  bore and depending on manip
 design,
  4in stroke, maybe as
  much as 6in stroke  is all you need.  Keep the
 rod
  size small at 5/8, that
  reduces the back  pressure.  I have said it
 before, I
  love convertible  top
  pumps.  Consider  using one pump per function
 again
  purchase from ebay for
  125  bucks.  No need  for valves, the pump
 simply
  runs in reverse to change
  direction of the  piston. Keep the pumps inside the
 sub
  and it is real
  simple.  As for the arm  itself, if have made
 them
  from cardboard first. 
  You  can mock it up that way  and find the best
  pin locations for the
  cylinders and ensure  the  cylinders 
 stroke
  properly without over
  centering. You can build the  arm with square 
  tubing, use 3 inch aluminum
  so the cylinders fit inside when  the arm is 
  folded up.  Forget about a
  wrist until you have lots of  time to play around.
   Four functions will serve a psubber well and can be
  built  for under 1,000
  dollars. I can send you a convertible top pump to play
  with  if you like.
   Hank
   --------------------------------------------
   On Wed, 5/28/14, swaters via Personal_Submersibles
  <personal_submersibles at psubs.org>
   wrote:

    Subject: [PSUBS-MAILIST] Manipulator arm
    To: personal_submersibles at psubs.org
    Received: Wednesday, May 28, 2014, 9:31 PM

    Hey guys. I am
    still working on the manipulator arm project for
  the  K  boats. I am a
  little overwhelmed as to what direction to  head.
 I 
  really don't know where
  to start because of my  lack of knolwedge. Does
  anyone  have any pointers as
  to where  to start? I am thinking about using
  electric  motors rather  than
  hydrolics just because of the amount of external 
  operating
  peices. Thanks,Scott  Waters

    Sent
    from my U.S. Cellular© Smartphone

    -----Inline Attachment Follows-----

    _______________________________________________
    Personal_Submersibles mailing list
    Personal_Submersibles at psubs.org

 http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

   _______________________________________________
   Personal_Submersibles mailing list
   Personal_Submersibles at psubs.org

 http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

   __________ Information from ESET NOD32 Antivirus,
 version
  of  virus
  signature  database 9862 (20140528) __________

   The message was checked by ESET NOD32 Antivirus.

   http://www.eset.com

   __________ Information from ESET NOD32 Antivirus,
 version
  of  virus
  signature  database 9862 (20140528) __________

   The message was checked by ESET NOD32 Antivirus.

   http://www.eset.com

   _______________________________________________
   Personal_Submersibles mailing list
   Personal_Submersibles at psubs.org

 http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

  _______________________________________________
  Personal_Submersibles mailing list
  Personal_Submersibles at psubs.org
  http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

  __________ Information from ESET NOD32 Antivirus, version
 of
  virus signature
  database 9866 (20140529) __________

  The message was checked by ESET NOD32 Antivirus.

  http://www.eset.com

  __________ Information from ESET NOD32 Antivirus, version
 of
  virus signature
  database 9867 (20140529) __________

  The message was checked by ESET NOD32 Antivirus.

  http://www.eset.com

  __________ Information from ESET NOD32 Antivirus, version
 of
  virus signature
  database 9867 (20140529) __________

  The message was checked by ESET NOD32 Antivirus.

  http://www.eset.com

  _______________________________________________
  Personal_Submersibles mailing list
  Personal_Submersibles at psubs.org
  http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

 _______________________________________________
 Personal_Submersibles mailing list
 Personal_Submersibles at psubs.org
 http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

 -----Inline Attachment Follows-----

 _______________________________________________
 Personal_Submersibles mailing list
 Personal_Submersibles at psubs.org
 http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles