[PSUBS-MAILIST] Bouyancy

Wed Jun 11 22:30:13 EDT 2014

One inch!!! No less.
Vance

-----Original Message-----
From: via Personal_Submersibles <personal_submersibles at psubs.org>
To: personal_submersibles <personal_submersibles at psubs.org>
Sent: Wed, Jun 11, 2014 9:54 pm
Subject: Re: [PSUBS-MAILIST] Bouyancy

Scott, Alec, Vance, and all,

A 3/4" vent is going to be about 2.25 times as big in cross section as the 1/2" vent.  A 1" vent would be about 4 times as big as the 1/2". What are your thoughts/comments on 3/4", 1" or any other size vent vs another?

Thanks,
Jim  

In a message dated 6/11/2014 5:45:10 P.M. Central Daylight Time, personal_submersibles at psubs.org writes:

James,

I totally agree with you on the 1/2 inch vents being way to small.   Eventually I am going to switch mine out to 3/4"

Thanks,

Scott Waters

Sent from my U.S. Cellular©   Smartphone

James Frankland via Personal_Submersibles   <personal_submersibles at psubs.org> wrote:

Hi All,

A member has asked me to post a description of what was going on with   bouyancy on my dive.  Which was as follows:

I'd asked the crane driver to be prepared for the first dive to hold me   just below the surface as i was expecting to be a little out of control.    

At first, i got a bubble stuck in the forward tank.  Ive put quite a   large lip on the inside of the tanks in an attempt to cope with Guernsey   seas.  I could see the bubble stuck through the forward dome and i   squished myself right up into the front to try and force it a bit more   level so it could escape out of the vent.  It didnt make any difference   and then all the lead i had inside, slid along the deck right to the back,   making the entire situation worse.  Closed vents, blew mains and   re-surfaced.

Next attempt, i got the bubble stuck in the aft tank.  This wasnt as   bad because the motor cut away allows air to escape so i got under a little   further, but not enough.  I flooded the variable in an attempt to get   under.  Still no good, so i asked the divers to shove on the back.    This got the boat under, but then because of the total lack of air in any   tanks, i sank to the bottom like a stone.  Depth was 6m (20ft).  I   expected to stop on the crane ropes, but the driver must have misunderstood me   and before i knew it, the bottom was in sight and then i was down with a   gentle bump.  

I sat for a bit talking to my brother on the radio and then shut the   variable vent and pumped a little air into the tank.  I slowely started   to rise.  Flooded it again and started to sink.  Really quite   straight forward.  

Blowing the VBT completely brought me up fairly quickly until i seemed to   be just awash with the surface.  Filling the mains then brought me right   out.  

I did several more test dives after that and as long as i evened out the   venting of the main tanks to avoid the bubbles, i could dive without the   divers assistance.  

I next got the boat neutral just off the bottom and then used the motors   to drive up and down. I was not aware at the time that one motor was not   working but it still seemed quite responsive and i could drive all the way up   to the top or down to the bottom, stopping anywhere in between.

I need to add some extra vents to the main tanks to prevent the air   pocket from occuring again, and also those half inch vents are far too   small.  It takes forever to vent the main tanks.  Thats one for a   winter modification.

I think that was it.

Regards

James

_______________________________________________
Personal_Submersibles   mailing   list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

_______________________________________________
Personal_Submersibles mailing list
Personal_Submersibles at psubs.org
http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.whoweb.com/pipermail/personal_submersibles/attachments/20140611/7705faf9/attachment.html>