[PSUBS-MAILIST] rpm

Sat Aug 30 12:49:41 EDT 2014

Jim, Thanks' I was going to ask what is the preferred oil.
I have been using WD40 for some time now and found no problems.  I did have a clear tube running to a motor and it hardened.  Other than that the motors I have are on their  third sub and still working.  I will make the switch to marvel mystery oil since I am now out of WD40. 
Hank 
--------------------------------------------
On Sat, 8/30/14, via Personal_Submersibles <personal_submersibles at psubs.org> wrote:

 Subject: Re: [PSUBS-MAILIST] rpm
 To: personal_submersibles at psubs.org
 Received: Saturday, August 30, 2014, 9:22 AM

 Hank,

 I don't know if you will find an oil with lower
 viscosity than WD40.  
 The problem with WD40 is that it is a solvent that damages
 plastic and rubber 
 components within the motor.  Alec Smyth did a lot of
 testing on various 
 oils.  The last I knew the medium of choice was Marvel
 Mystery Oil.  
 It's safe for the seals, etc., and has a lower viscosity
 than any straight 
 mineral oil.

 For thrusters, comparative amp draw at a given RPM
 (with associated heat 
 build-up) is probably more significant than drop in maximum
 RPM since we're 
 not generally operating at maximum.  That might not be true
 when you're 
 using the motor to operate a pump.

 Jim

 In a message dated 8/30/2014 5:51:09 A.M. Central
 Daylight Time, 
 personal_submersibles at psubs.org writes:
 Brian,
 Yes, I have heard others have had good success
 with 
   different oils.  Maybe the rpm drop is less with other
 oils.  

 Hank
 --------------------------------------------
 On Fri, 8/29/14, 
   Brian Cox via Personal_Submersibles
 <personal_submersibles at psubs.org> 
   wrote:

 Subject: Re:
 [PSUBS-MAILIST] rpm
 To: "Personal
 Submersibles 
   General Discussion"
 <personal_submersibles at psubs.org>
 Received: 
   Friday, August 29, 2014, 11:26 PM

 Hank, There is a very thin 
   mineral
 oil that might be better that the
 wd 40

 Brian

 --- 
   personal_submersibles at psubs.org
 wrote:

 From: hank pronk via 
   Personal_Submersibles
 <personal_submersibles at psubs.org>
 To:
 Personal 
   Submersibles General Discussion 
   <personal_submersibles at psubs.org>
 Subject: Re: [PSUBS-MAILIST] 
   rpm
 Date: Fri, 29 Aug 2014 13:23:31
 -0700

 Vance,
 Yes for sure, 
   Gamma has two separate amp gauges, one for the
 motor and one for the rest 
   of the sub. All 24v and the
 trolling motor
 is 12 v
 Hank 

 --------------------------------------------
 On Fri, 8/29/14, via 
   Personal_Submersibles 
   <personal_submersibles at psubs.org>
 wrote:

 Subject: Re: 
   [PSUBS-MAILIST] rpm
   To:
 personal_submersibles at psubs.org

   Received: Friday, August 29, 2014, 4:03 PM

   Yeah, 
   too
   simple. Maybe that's a good
 guess, but..... I will say

   that an ammeter in the boat is a good thing. You can
 keep
 an
   eye 
   on things, and if it goes UP at some stage, you would
   suspect a 
   thruster issue (a tangle, or a bearing failure
 or
   whatever). All 
   it takes is an appropriate shunt and a
 gauge
   (in my pre-digital 
   steampunk mind). Okay, thanks anyway. I

 was curious, that's 
   all.
   Vance

   -----Original
   Message-----

   From: hank pronk via
 Personal_Submersibles

   <personal_submersibles at psubs.org>

   To: Personal 
   Submersibles General Discussion

   <personal_submersibles at psubs.org>

   Sent: Fri, Aug 
   29, 2014 3:56 pm

 Subject: Re: [PSUBS-MAILIST] 
   rpm

   Vance,
   I did not do an 
   amp draw test because I do not have the

 technology in house. I 

   would guess with a 10% rpm drop, there
 may be a 10% amp

   increase. That would be 
   to simple
 :-)

   Hank

 --------------------------------------------
   On Fri, 
   8/29/14, via Personal_Submersibles 
   <personal_submersibles at psubs.org>

   wrote:

   Subject: Re: [PSUBS-MAILIST] rpm
   To: 
   personal_submersibles at psubs.org

 Received: Friday, August 29, 2014, 
   3:39 PM

   Hank,
   Did you check the amperage? I 
   wonder if the
   resistance causes a
 higher draw, and if so, 
   how
   much?

   Vance

   -----Original

   Message-----

   From:
 hank pronk via 
   Personal_Submersibles

   <personal_submersibles at psubs.org>

   To: 
   personal_submersibles

   <personal_submersibles at psubs.org>

   Sent: Fri, Aug 
   29, 2014 3:33 pm

 Subject: [PSUBS-MAILIST] rpm

   I am working on a
 hydraulic
   pump that will be 
   external and pressure compensated 
   in
 oil.  I am using a 
   trolling motor to drive
 the pump.  A
   while back there was 

   a question about rpm drop when a
 trolling motor 
   is
 filled
   with oil.  I
 bench 
   tested that today, 
   and the motor runs at 2,000rpm
 stock
 and
   1,800 rpm full of 

   WD40.
   Hank

   _______________________________________________

   Personal_Submersibles mailing list

   Personal_Submersibles at psubs.org

 http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

   -----Inline Attachment Follows-----

 _______________________________________________

   Personal_Submersibles mailing list

   Personal_Submersibles at psubs.org

 http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

 _______________________________________________

   Personal_Submersibles mailing list

   Personal_Submersibles at psubs.org

 http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

   -----Inline
 Attachment Follows-----

   _______________________________________________

   Personal_Submersibles mailing list

   Personal_Submersibles at psubs.org

 http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

 _______________________________________________
 Personal_Submersibles 
   mailing 
   list
 Personal_Submersibles at psubs.org
 http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

 _______________________________________________
 Personal_Submersibles 
   mailing 
   list
 Personal_Submersibles at psubs.org
 http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles

 _______________________________________________
 Personal_Submersibles 
   mailing 
   list
 Personal_Submersibles at psubs.org
 http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles
 -----Inline Attachment Follows-----

 _______________________________________________
 Personal_Submersibles mailing list
 Personal_Submersibles at psubs.org
 http://www.psubs.org/mailman/listinfo.cgi/personal_submersibles