[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
RE: [PSUBS-MAILIST] Controller/Display
Jon,
You might want to check out http://www.os-rc.com/ It's an open source RC controller transmitter.
Not super cheap, but pretty cool. It's modular so you can add additional control functions.
-andy
-----Original Message-----
From: owner-personal_submersibles@psubs.org [mailto:owner-personal_submersibles@psubs.org] On Behalf Of Greg
Sent: Wednesday, April 04, 2012 9:10 AM
To: personal_submersibles@psubs.org
Subject: RE: [PSUBS-MAILIST] Controller/Display
Hi Jon,
You can find a number of controllers that will work with the type of joystick in your picture by perusing the "battle-bot" websites. A lot of these guys are using two channel PWM controls designed for tractor drives- but they will work just fine for a pair of thrusters. Most of these units are designed to be used with joysticks that have 5k pots and drive voltages up to about 50v.
You should be able to set up the whole thing for less than $500.
Greg
-----Original Message-----
From: owner-personal_submersibles@psubs.org
[mailto:owner-personal_submersibles@psubs.org] On Behalf Of Jon Wallace
Sent: Wednesday, April 04, 2012 2:47 AM
To: personal_submersibles@psubs.org
Subject: [PSUBS-MAILIST] Controller/Display
I found a photo that pretty that much looks like what I want to create in terms of a remote motor controller and sensor display. The photo labeled controller-1 was designed for a robot and so had four thumb-joysticks and many more switches than would be necessary for a submarine.
I will be looking to use two joysticks, one on the left for up/down, one on the right for forward/reverse/left/right. They will both be two axis joysticks even though only one axis is necessary for the up/down thrusters. The photo marked joystick-1 is what I have selected to start off with. The thumb-joysticks shown in the robot controller are cheap, and work, but they don't appear to have the resolution that I think I want for the thrusters based upon what I've seen in various youtube videos of other projects. It's not clear to me that the joysticks I have selected have adequate resolution either, but they appear to be better than the thumb-joysticks and at only $25 (us) each I'm willing to take a chance on them. Industrial joysticks look like they cost anywhere between $600-$1000.
For the display, I'll be using a 20x4 Red LCD (4 lines of 20 characters
each) and will cycle through various menus since not all the sensor information will fit on four lines. Currently planning on depth, vertical-rate, water pressure, cabin pressure, water temp, cabin temp, and also thinking about having a data logger to save all the sensor information during the dive.
I was going to also include a luminosity sensor (thanks Jens for the ebay pointer) but the cheap LDR's are apparently not very consistent so I'm going to wait on it and add one later.
Still looking for a 50amp motor controller that can handle 36vdc before I seek out Alec's friend to design one. I'm not quite sure what the barrier is but I notice most reasonably priced motor controllers that handle large current seem to have a limit of 30vdc.
Jon
************************************************************************
************************************************************************
************************************************************************
The personal submersibles mailing list complies with the US Federal CAN-SPAM Act of 2003. Your email address appears in our database because either you, or someone you know, requested you receive messages from our organization.
If you want to be removed from this mailing list simply click on the link below or send a blank email message to:
removeme-personal_submersibles@psubs.org
Removal of your email address from this mailing list occurs by an automated process and should be complete within five minutes of our server receiving your request.
PSUBS.ORG
PO Box 53
Weare, NH 03281
603-529-1100
************************************************************************
************************************************************************
************************************************************************
************************************************************************
************************************************************************
************************************************************************
The personal submersibles mailing list complies with the US Federal
CAN-SPAM Act of 2003. Your email address appears in our database
because either you, or someone you know, requested you receive messages
from our organization.
If you want to be removed from this mailing list simply click on the
link below or send a blank email message to:
removeme-personal_submersibles@psubs.org
Removal of your email address from this mailing list occurs by an
automated process and should be complete within five minutes of
our server receiving your request.
PSUBS.ORG
PO Box 53
Weare, NH 03281
603-529-1100
************************************************************************
************************************************************************
************************************************************************