[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[PSUBS-MAILIST] Interesting Link on Stiffeners and Steel Plate.

To: <personal_submersibles@psubs.org>
Subject: [PSUBS-MAILIST] Interesting Link on Stiffeners and Steel Plate.
From: "Stephen Pearce" <sjpearceqld@bigpond.com>
Date: Fri, 5 Jan 2007 13:15:25 +1000
Importance: Normal
In-reply-to: <471668B937C2894B818E2FB7E561159D35848E@nasa-dtw-ex004.nasa.cpwr.corp>
Reply-to: personal_submersibles@psubs.org
Sender: owner-personal_submersibles@psubs.org
This link may be of interest to some of members.

www.civil.ualberta.ca/structures/reports/SER236Sheikh,Grondin,andElwi.pdf 

Steve P

-----Original Message-----
From: Smyth, Alec [mailto:owner-personal_submersibles@psubs.org] On Behalf
Of Smyth, Alec
Sent: Friday, 5 January 2007 5:42 AM
To: personal_submersibles@psubs.org
Subject: RE: [PSUBS-MAILIST] Thrust from a pump?

For centrifugal pumps (the most common kind) that's true, they only run one
way. But there are pumps that can run in either direction with the same
efficiency. Problem is, from what I've see so far their efficiency is very
low. Using Cliff's formula, it looks like they would not provide enough
thrust.
 
Alec

  _____  

From: owner-personal_submersibles@psubs.org on behalf of vbra676539@aol.com
Sent: Thu 1/4/2007 2:12 PM
To: personal_submersibles@psubs.org
Subject: Re: [PSUBS-MAILIST] Thrust from a pump?


Pumps do run in one direction, right? Running one backwards is
inefficient. Change the flow downstream. Vance 
 
 
-----Original Message-----
From: nomdae@hotmail.com
To: personal_submersibles@psubs.org
Sent: Thu, 4 Jan 2007 2:07 PM
Subject: RE: [PSUBS-MAILIST] Thrust from a pump?


I had to replace the motor on my pool pump last summer. Six bolts held the
motor against the pump housing.  To disconnect the impeller, I simply put a
screwdriver into the motor to prevent it from turning and unscrewed the
impeller off of the motor shaft with my hands.
My concern is that some pool pumps are designed to run in only one
direction, and that reversing one would either not work at all, or could
make it fall apart.
-- NP


  _____  

From:  "Smyth, Alec" <Alec.Smyth@compuware.com>
Reply-To:  personal_submersibles@psubs.org
To:  <personal_submersibles@psubs.org>
Subject:  RE: [PSUBS-MAILIST] Thrust from a pump?
Date:  Thu, 4 Jan 2007 11:50:42 -0500
>Yes, and in addition depending on the type of pump a thrust bearing
>could be on the wrong end of the shaft in "reverse".
>
>Lots of food for thought here...
>
>Alec
>
>-----Original Message-----
>From: owner-personal_submersibles@psubs.org
>[mailto:owner-personal_submersibles@psubs.org] On Behalf Of Dan H.
>Sent: Thursday, January 04, 2007 9:45 AM
>To: personal_submersibles@psubs.org
>Subject: Re: [PSUBS-MAILIST] Thrust from a pump?
>
>But Alec,
>Wouldn't using a reversible pump as a thruster require you to use two
>small output nozzles instead of a larger suction input and ported down
>output nozzle.  I'm not sure if the pump would like that. Sounds like a
>cavation problem.
>
>Maybe a single direction pump and a Y valve to two separate output
>nozzles?????
>
>Dan H.
>----- Original Message -----
>From: "Smyth, Alec" <Alec.Smyth@compuware.com>
>To: <personal_submersibles@psubs.org>
>Sent: Thursday, January 04, 2007 9:16 AM
>Subject: RE: [PSUBS-MAILIST] Thrust from a pump?
>
>
>Wow, what an A+ response! Thanks Brian for yours as well. With this
>information I can now go out and do some virtual shopping to see how
>much
>I'd have to spend to accomplish the same thrust with the two approaches.
>Off
>hand I'd say the well pump solution would likely be cheaper, but mating
>trolling motors to pump heads makes use of two brand new trolling motors
>I
>happen to have sitting in the garage.
>
>thanks,
>
>Alec
>
>________________________________
>
>From: owner-personal_submersibles@psubs.org on behalf of Cliff Redus
>Sent: Wed 1/3/2007 8:58 PM
>To: personal_submersibles@psubs.org
>Subject: Re: [PSUBS-MAILIST] Thrust from a pump?
>
>
>
>Alec,
>
>
>
>Below is a derivation of thrust that can be developed from a axial flow
>pump
>in terms of volumetric flowrate.
>
>
>
>The thrust due to accelerating fluid through a pump can be written as
>
>
>
>F=M(V1-V0)
>
>
>
>Where M is the mass flow rate, V0 is the free stream velocity upstream
>of
>the pump and V1 is the velocity exiting the pump.
>
>
>
>But the mass flow rate M can be related to the volumetric flow rate Q as
>
>
>
>M=Density*Q
>
>
>
>Substituting, the thrust in terms of volumetric flow rate is
>
>
>
>F=Density*Q(V1-V0)
>
>
>
>But the volumetric flow rate Q is related to velocity in the pump duct
>ID as
>
>
>
>Q=V1*A=V1*Pi*D^2/4
>
>
>
>Where D is the duct ID.
>
>
>
>Solving for V1, and substituting, the thrust can be written as
>
>
>
>F=Density*Q(Q/(Pi*D^2)-V0)
>
>
>
>For a thruster oriented approximately normal to the direction of flow,
>the
>inlet velocity can be assumed to be zero.  The thrust then reduces to
>
>
>
>F = 4*Density*Q^2/(Pi*D^2)
>
>
>
>Or
>
>
>
>F= 0.001766*(q/d)^2
>
>
>
>for freshwater where,
>
>
>
>F = Thrust, lbf
>
>q =  pump volumetric flow rate in gpm
>
>d = pump outlet duct inside diameter in inches
>
>
>
>As an example, a pump with a capacity of 200 gpm flowing through a 2"
>duct
>would develop 17.7 lbf of thrust.
>
>Cliff
>
>
>----- Original Message ----
>From: "Smyth, Alec" <Alec.Smyth@compuware.com>
>To: personal_submersibles@psubs.org
>Sent: Wednesday, January 3, 2007 4:20:48 PM
>Subject: [PSUBS-MAILIST] Thrust from a pump?
>
>
>
>I'm contemplating using water pumps as maneuvering thrusters (NOT for
>main
>propulsion). Cousteau's socoupe used a hydraulic pump for the jets, but
>I'd
>like to avoid that route if possible due to the excessive noise. DC
>submersible pumps are convenient but I haven't found anything beefy. I
>could
>try mating a trolling motor to a pump head. Submersible well pumps look
>promising because they're very powerful yet compact, but they require
>AC,
>and I don't think I can reverse them so I'd need four pumps instead of
>two.
>I could of course hang trolling motors off the boat font and back, but
>it
>really messes up the hydrodynamics of what can otherwise be a quite
>clean
>design, and the props on my trolling motors make them too large to duct
>into
>the MBTs.
>
>Assuming I do settle on some kind of pump, the next question is how
>strong
>it needs to be. Does anyone know how to translate GPM (or LPM) into
>static
>thrust?
>
>Any ideas or experiences would be much appreciated.
>
>
>Thanks,
>
>Alec
>
>The contents of this e-mail are intended for the named addressee only.
>It
>contains information that may be confidential. Unless you are the named
>addressee or an authorized designee, you may not copy or use it, or
>disclose
>it to anyone else. If you received it in error please notify us
>immediately
>and then destroy it.
>
>
>
>
>
>
>************************************************************************
>************************************************************************
>************************************************************************
>The personal submersibles mailing list complies with the US Federal
>CAN-SPAM Act of 2003.  Your email address appears in our database
>because either you, or someone you know, requested you receive messages
>from our organization.
>
>If you want to be removed from this mailing list simply click on the
>link below or send a blank email message to:
> removeme-personal_submersibles@psubs.org
>
>Removal of your email address from this mailing list occurs by an
>automated process and should be complete within five minutes of
>our server receiving your request.
>
>PSUBS.ORG
>PO Box 53
>Weare, NH  03281
>603-529-1100
>************************************************************************
>************************************************************************
>************************************************************************
>
>The contents of this e-mail are intended for the named addressee only. It
contains information that may be confidential. Unless you are the named
addressee or an authorized designee, you may not copy or use it, or disclose
it to anyone else. If you received it in error please notify us immediately
and then destroy it.
>
>
>
>
>************************************************************************
>************************************************************************
>************************************************************************
>The personal submersibles mailing list complies with the US Federal
>CAN-SPAM Act of 2003.  Your email address appears in our database
>because either you, or someone you know, requested you receive messages
>from our organization.
>
>If you want to be removed from this mailing list simply click on the
>link below or send a blank email message to:
> removeme-personal_submersibles@psubs.org
>
>Removal of your email address from this mailing list occurs by an
>automated process and should be complete within five minutes of
>our server receiving your request.
>
>PSUBS.ORG
>PO Box 53
>Weare, NH  03281
>603-529-1100
>************************************************************************
>************************************************************************
>************************************************************************
>



  _____  

Dave vs. Carl: The Insignificant Championship Series.  Who will win?
************************************************************************
************************************************************************
************************************************************************ The
personal submersibles mailing list complies with the US Federal CAN-SPAM Act
of 2003. Your email address appears in our database because either you, or
someone you know, requested you receive messages from our organization. If
you want to be removed from this mailing list simply click on the link below
or send a blank email message to: removeme-personal_submersibles@psubs.org
Removal of your email address from this mailing list occurs by an automated
process and should be complete within five minutes of our server receiving
your request. PSUBS.ORG PO Box 53 Weare, NH 03281 603-529-1100
******************************! ******************************************
************************************************************************
************************************************************************ 
  _____  

Check out the new AOL. Most comprehensive set of free safety and security
tools, free access to millions of high-quality videos from across the web,
free AOL Mail and more.

The contents of this e-mail are intended for the named addressee only. It
contains information that may be confidential. Unless you are the named
addressee or an authorized designee, you may not copy or use it, or disclose
it to anyone else. If you received it in error please notify us immediately
and then destroy it. 
The contents of this e-mail are intended for the named addressee only. It
contains information that may be confidential. Unless you are the named
addressee or an authorized designee, you may not copy or use it, or disclose
it to anyone else. If you received it in error please notify us immediately
and then destroy it. 






************************************************************************
************************************************************************
************************************************************************
The personal submersibles mailing list complies with the US Federal
CAN-SPAM Act of 2003.  Your email address appears in our database
because either you, or someone you know, requested you receive messages
from our organization.

If you want to be removed from this mailing list simply click on the
link below or send a blank email message to:
	removeme-personal_submersibles@psubs.org

Removal of your email address from this mailing list occurs by an
automated process and should be complete within five minutes of
our server receiving your request.

PSUBS.ORG
PO Box 53
Weare, NH  03281
603-529-1100
************************************************************************
************************************************************************
************************************************************************
Follow-Ups:
- RE: [PSUBS-MAILIST] Interesting Link on Stiffeners and Steel Plate.
  - From: "Jon Wallace" <jon@psubs.org>
References:
- RE: [PSUBS-MAILIST] Thrust from a pump?
  - From: "Smyth, Alec" <Alec.Smyth@compuware.com>
Prev by Date: RE: [PSUBS-MAILIST] Thrust from a pump?
Next by Date: Re: [PSUBS-MAILIST] Thrust from a pump?
Previous by thread: RE: [PSUBS-MAILIST] Thrust from a pump?
Next by thread: RE: [PSUBS-MAILIST] Interesting Link on Stiffeners and Steel Plate.
Index(es):
- Date
- Thread